If you have a winter cover, remove it. For solid covers pump the water from the cover, underneath the cover, back into the pool. Add water to proper level. Connect filter and pump. For d.e. filters open air bleed knob on filter until water shoots out. Add recommended amount of d.e. filter powder slowly into the skimmer. When pressure gauge is 10 lbs. Over clean running pressure the filter needs to be cleaned. Cut the chlorine pack a 1/2” below the recommended cut line for optimal chlorination. With filter off, turn chlorinator adjustment knob to closed position. Open cover and insert chlorine pack Turn adjustment knob to 4 for the first day. Turn up by one increment daily as needed to achieve optimal chlorine dispersion. When getting a level chlorine reading leave knob at that level. Check the chlorine pack after 3 weeks. Do not store chlorine packs near any pool or other equipment as the vapors are extremely corrosive. Maintain proper chlorine and PH levels and have water tested regularly to maintain total water balance.

Attach pole to vacuum head. Connect vacuum hose to the vacuum head. Connect skim vacuum to other end of the vacuum hose. Place vacuum head and pole in water. With pool running, hold the skim vacuum over the return to fill hose with water. best price dyson handheld vacuum cleanerWhen vacuum head bubbles to the top of pool and sinks, hose is full. carpet cleaning coupons buffalo nyPlace skim vacuum over basket in the skimmer. steam carpet cleaning benefitsMake sure pump is full of water and move vacuum head slowly across the bottom of the pool to vacuum. carpet cleaner hire sa

When done vacuuming remove vacuum head from the water. Remove skim vacuum and clean basket in skimmer. Do not try to remove the skim vacuum before removing vacuum head from the water. best steam mop for oak floorsThere is too much suction and you can damage the skimmer and other equipment.best thing to use to clean vinyl siding Please take the time to read these simple pool closing instructions. best carpet cleaning allergiesBecause of our winter climate and snow buildup, we have to take extra precautions when closing our pools for the season. If you have any questions at all please call Century Pools at 1-207-465-3475. As always we test water for free and have closing supplies available to you.As always we test water for free and have closing supplies available to you.

Doing a BackwashTo do a backwash you need to turn off pool pump, turn filter head to the position of the backwash setting, un roll the flexible blue discharge hose to a designated area then turn back on the pool pump and leave running for about three to five minutes, this will remove the dirt from the filter sand. Once three to five minutes past, turn off pool pump again turn filter handle position to rinse and turn back on pool pump for about 30 seconds, this will clean the filter head and pipe of the excess debris this help to prevent the debris to flow back in the pool. Once rinse is done turn pump back off turn filter handle back to filter and that’s it. Vacuuming your poolWhen you need to vacuum your pool make sure filter dial valve is set to the filter position unless you are vacuuming algae. Attach the vac pole to the vac handle. Put the vac head with pole and hose attached to it into the pool. Fill the vac hose with water two ways to do so, first by placing the end over the return fitting you will see the air coming out of the vacuum head in the bottom of the pool.

Second is to stay next to skimmer and bring down the vacuum hose downwards and fill hose by gravity.Put in vacuum plate inside the skimmer over the basket, then when hose is full of water put your hand over then end to prevent water from draining back in pool and bring hose end over top of skimmer and put in vacuum plate. Then start vacuuming once done do not pull on hose has it may break. Need to turn off pump to relieve pressure. Remove hose, remove vacuum plate and empty the basket and reinstall in skimmer. Vacuuming the pool is required pretty much only when it’s dirty.Why wont my pool lights turn on?Where are the bubbles coming from in my pool?Why is my pump not working?Why is my pump running but there is no pressure?Why is my pump running hot and cutting off?Why is my pump very noisy?Why wont my pump not prime?Why do I find sand at the bottom of the pool?Why is my pool water murky or cloudy it will not stay clear?Why is the pressure on my filter gauge indicating high pressure?Why is water leaking from the waste pipe of my filter?

First check breakers in the house to see if they are trip then check the light transformers to see if that’s trip. If transformer and breakers are not trip then the light may have burnt out and needs to be replaced. Most light manufacture can replace the light bulb without drawing the pool.First check the pump lid, check if it’s loose or check if the gasket is damaged. You can start by lubricate gasket or replace the cover or gasket if necessary.Second make sure the water level in pool is ¾ full through the opening of the skimmer. Put your garden hose in the pool and raise water level and may solve problem.Third there could be a leak in the suction plumbing line or skimmer. To determine if there is a leak a technician has to come over to do a pressure test. This will help determine if there’s a leak has because it’s a suction line you may not loose water in pool.First check the power, breakers, switches etc. If you have a timer on the system, make sure it is functioning properly.

This can be caused by a dirty filter or a blocked return line, dirt or toys etc. Second option is that the pump impeller is dirty and not working properly and need to be clean, this can be done by the home owner or service technician.What’s happening is that pool pumps have a thermal cut off which will shut the motor off when it gets too hot, and will restart itself once it has cooled off. If this is an ongoing problem, your pump motor is likely at the end of its life and will have to be replaced.The pump can be noisy, it can be due to vibration which you can fix that by putting rubber spacers under the pump. If pump is making a squealing high pitch noise this can be a sign that you pump bearing are wearing down and may need to replace the bearings or purchase new pump.First thing check pump lid and make sure it is tight also check cover O-ring to make sure it is install and not dry or crack if so lubricate O-ring or replace. Second your pump may not prime do to a suction leak which allows air to enter pump.

This would require a pressure test by a technician. Third there may be an obstruction in the suction line, dirt or toys. You can rent or buy a plumbers snake to dislodge the obstruction. Last but not least make sure water level in pool is at the right range ¾ full in the skimmer.If there is sand at the bottom of the pool that maybe cause by a loose or broken pipe located at the bottom of the filter. Sand can also come if your pool pump may is too big for your filter. During backwashing the pressure can cause the sand to rise high enough to overflow into the standpipe, allowing sand to flow back into the pool. Sometimes what we assume looks like sand can be cause by undissolved chemicals, granular chlorine or tablets, contains a percentage of material called inert. This is calcium residue, or dust, which many pool owners mistake for sand.This can be cause by different things. First thing you need to make sure is that pool is properly balance, ph, alkalinity, hardness and stabilizer. Have your pool water test by a professional has the home made kit are not has precise.