Skip To Main Content Skip To Main Navigation Change Your Font Size: Not a user yet? Sign up to receive our Hayward POOLSIDE™ Newsletter! The file you are attempting to access is no longer available at this location. Please check the URL If you are a pool owner looking for product information, want to find a pool professional in your area, or are looking for general information on Hayward Pool Products, please visit If you are planning on getting pool and need help planning and envisioning the possibilities, please visit If you are a pool professional and would like information regarding Hayward's Totally Hayward Partner program,Pump or siphon all water from cover before attempting to remove it. Use a long- handled net or “leaf rake” to remove leaves and debris. Using a submersible cover pump, pump the water from the cover. (Cover pumps are available at Pettis Pools.) Do not pump the water from the cover into the pool, as it most likely contains bacteria and algae.

This can make getting your water ready for the season much more difficult. Carefully remove the cover for cleaning and storage. We hope you got the cover off without spilling any of the leaves and debris into the pool….but if you didn’t, check out our “leaf bagger” tool that you hook up to your garden hose and vacuum pole. It does a great job of getting things out of the bottom of your pool without putting them through the filter. It’s fast too – and it’s available here at Pettis.Vacuum your pool if needed. If there is a great deal of debris, we recommend that on sand filters, you vacuum to “waste” to avoid putting it back into your filter. NEVER VACUUM ON BACKWASH!!! Vacuum using either the “filter” or the “waste” position.Fill your pool to the correct water level so that the skimmer can operate properly. Check your filter, hoses, filter media, etc. to make certain that your filter will work effectively. If you have a sand filter, either chemically clean the sand or replace it (preferred by most people with above ground pools).

If you’re going to replace the sand, the best time to do so is before you fill the pool. Begin circulating the water. Trouble with your filter pump and/or motor? Yes, we do repairs, with replacement of bearings and seals the most common. The repair is usually completed within 3 to 5 days depending on the time of year. We also carry a complete line of parts, gaskets, impellers, etc. and will give you all the advice we can if you wish to tackle the job yourself. carpet cleaning remedies pet stainOr, maybe it’s time for a new pump? carpet cleaning companies delawareYes, we have those too.best portable carpet cleaner for stairsTest your water, using new reagents or test strips. las vegas pools open to locals 2015

Old reagents or test strips could give you a false reading and you may spend your time and money trying to correct a problem that doesn’t exist – or not knowing about a problem that is there. Adjust your pH to 7.2-7.6 first and if possible, the alkalinity should also be tested and adjusted if necessary. Add the algaecide and shock as per the directions in the Opening Kit and let water circulate for 8-12 hours.Bring in a sample of pool water anytime after that, taken at least 18 inches below the surface, in a clean glass jar or a water sample bottle. best carpet stain and odor removerA number of tests will be performed using the most advanced water test technology available, and a computerized printout will tell you the condition of your pool water and advise what, if any, corrective measures should be taken to bring your water into balance. pool cleaning winter haven

There is currently no charge for this service at our water test center. We cannot guarantee our results for any brands other than poolife®, Baquacil®, Ultima®, FROG® or EZ Pool® as our software is designed based on the quality of the products we carry.If you are using Chlorine as a sanitizer, do not add stabilizer until your water is tested and the results show that you really need it. Too little stabilizer (also called conditioner) will result in loss of chlorine to the ultraviolet rays of the sun; too much could reduce the effectiveness of your chlorine.Once your pool water is properly adjusted, follow regular maintenance procedures and enjoy!If you ever do have a problem, we are here to help. Maintaining a pool is easy if you get off to a good start. If you have any questions specific to your pool or filter, please give us a call or come in to see us. We are always glad to help!/blog/hot-tubs-and-spas/why-you-should-purchase-your-pool-chemicals-from-pool-professionalsWe invite you to share your positive experience with our company with others.

If you would please take a moment to visit the home page of our website, click on the Review this Biz link in the lower right-hand corner, and leave a review we would greatly appreciate it.Click here to download PDFAs warm weather approaches, the pool owner’s thoughts turn to swimming and family fun. While we cannot anticipate every circumstance, this section attempts to address the most common issues about pool opening. The more you know about opening your pool, the more you will enjoy your pool all season. REMOVE THE LEAVES FROM THE COVER Be sure to remove the leaves from the cover so they do not drop into the pool when you take the cover off. There are many tools to assist you in getting the leaves off the cover. A leaf skimmer or leaf net works well for light duty, or if there are a lot of leaves you may want to use a leaf vacuum. SIPHON OR PUMP OFF THE POOL COVER The purpose of covering the pool during the winter is to keep it clean of debris and odor-free. Any stagnant water on top of the cover should be pumped away from the pool.

Avoid letting the standing water get into the pool. REMOVE, WASH, DRY AND STORE THE COVER One step people often skip is washing the cover. You are about to store the cover away for an entire hot, humid summer. The last thing you'll want is to pull it out in September and find a musty, mildew mess. An easy way to wash the cover is with an 18” wall/algae brush attached to your vacuum pole, and a mild, effective pool cover cleaner. Wash all air pillows and water tubes as well. Allow them to dry in sunlight. Then, fold them neatly and store them in a safe, out of the way area for the summer. REMOVE ALL WINTERIZING PLUGS, PLATES AND GIZZMOS Make sure to remove all winterizing plugs, plates and gizzmos covering the thru-wall skimmer and any of the thru-wall return lines. These are located on the inside walls of the swimming pool. If you own an in-ground pool, these lines should have antifreeze in them. Don’t worry about antifreeze leaking back into the pool. Robelle Pool Antifreeze is non-toxic usually amounting to less than 6 gallons, which when mixed with more than 20,000 gallons of pool water will not impact your pool or its swimmers.

CHEMICALLY CLEAN THE FILTER Chemically clean the filter if it was not chemically cleaned before closing for the winter. Filters should be chemically cleaned at least twice a year to operate efficiently during the swimming pool season. See the label on Robelle Filter Cleaner to properly chemically clean your filter. RECONNECT THE FILTER, PUMP AND MOTOR If you have a cartridge filter make sure all cartridges are clean before use. Close or cap the filter drain on the bottom of the filter tank. If there are any o-rings that belong in any of these connections, lubricate them with a non-petroleum-based lubricant before reconnecting. If you have a sand filter, make sure the filter is filled with the appropriate amount of Robelle White Filter Sand (usually half to two-thirds full). If you add more sand, rinse it before closing the tank. This will prevent the dust from going into the pool when you turn the filter on, clouding the water. Fittings will need to be reconnected that were disconnected between the pump, filter, motor, chemical feeder, automatic vacuum line, and heater (not all pools have chemical feeders, automatic vacuum lines or heaters).

CHECK THE POOL SYSTEM A full check of the pool system will need to be done to see that it works properly. Make sure the power supply to the pump is live, and turn on the motor, just for a couple of seconds, to make sure the motor itself is indeed working and not seized. Turn it off immediately. (Never run your pump and motor for extended periods without water running through it). If the motor appears seized, noisy, or does not work, you'll need to have it serviced immediately. Check the filter system and skimmer basket to see that they are working properly. Follow manufacturer’s instructions for your type of filter. You should run your filter continuously for 48 to 72 hours initially for best results, or a minimum of 10 hours a day. FILL THE SWIMMING POOL Fill the pool to the appropriate water level, which would be half way up the faceplate of the thru-wall skimmer. CLEAN THE WATER LINE AND REMOVE LEAVES AND OTHER DEBRIS FROM THE SKIMMERS, POOL WATER, SURFACE AND BOTTOM

Should there be a waterline ring around the pool, now is the time to attack that, using rubber gloves, a good scrubber (stronger than a sponge but not as harsh as steel wool) and Robelle Concentrated All Purpose Cleaner. Brush the walls and steps especially if algae are present. REINSTALL THE LADDERS, STAIRS, RAILINGS, DIVING BOARDS, SLIDES AND OTHER ENTRANCE ACCESSORIES TURN ON THE FILTER AND VACUUM THE POOL If you have a DE filter system, you will need to add diatomaceous earth to the filter (according to the filter label instructions) as soon as you turn on the system. NOTE: Try not to manually vacuum a lot of leaves. Leaves can clog the vacuum hose, skimmer and filter baskets, and pool filter. A heavy concentration of leaves should be removed with a leaf vacuum. CHECK YOUR TEST KIT Test Kits do expire. Check your kit for an expiration date to make sure the test reagents and/or strips are still active to use. If not, discard and replace them. ROBELLE CONCENTRATED MINERAL REMOVER

This chemical is usually the first thing you need to add to the pool. This will need to circulate for 12 to 24 hours before you add any other chemical. In areas of high mineral content, we recommend adding two doses, filtering for 12 hours between doses. Test your pool water for alkalinity and pH (not the same thing). First, bring the alkalinity to a level of 100 ppm. Generally, one pound of Robelle Total Alkalinity will bring 7,500 gallons of pool water up 8 ppm. Run the filter for at least 4 hours before adding any other chemicals. Your pool water’s pH should measure between 7.2-7.6 and should be brought into range by adding Robelle pH Rise or Robelle pH Lower. Run the filter for at least 4 hours before adding any other chemicals. Now is the appropriate time to shock your pool. One gallon of Robelle Liquid Shock Treat (or one pound of Robelle Powdered Shock) properly treats 10,000 gallons of pool water. Circulate the pool water for at least 4 hours before adding any other chemicals.

Every swimming pool should be treated with an initial dosage of concentrated algaecide at this point. You should use algaecide routinely all season long to prevent algae growth and build-up, as directed on the container. NOTE: If you use a biguanide product, or if you have a gunite or concrete pool, do not use an algaecide with a copper-based active ingredient as it will stain your pool. Robelle Algaestroy 50 or Robelle Black Algaecide contains no metals, so it won’t stain. Now you can finally begin using the Robelle chlorine of your choice. If you choose to sanitize with unstabilized chlorine, or stabilized chlorine your stabilizer (cyanuric acid) level should measure between 30-50 ppm. Your pool water may be brought within this range by adding Robelle Stabilizer and Conditioner. This will greatly increase your chlorine effectiveness by reducing chlorine loss from the sun’s ultraviolet rays. Test your pool weekly and more often when there is excessive rain, evaporation or greater bather loads than usual.