User ReviewedHow to Clean Grout Between Floor Tiles Four Methods:Using Baking Soda and VinegarCleaning with Oxygenated BleachCleaning Grout with Hydrogen Peroxide, Baking Soda, and Dish SoapCleaning Grout with a Steam CleanerCommunity Q&A Even after mopping, tile floors with dirty grout may still look messy. You can make your floors look fresher by cleaning the grout between the tiles. This wikiHow will show you how to do that. Apply a paste made from baking soda and water to the grout. Spray it down with diluted vinegar. Scrub it with a brush, rinse it, then wipe it dry. Pour a solution made from oxygenated bleach and warm water onto the grout. Scrub it with a brush, rinse it, then mop it up. Use a brush to scrub a paste made from hydrogen peroxide, baking soda, and dish soap into the grout. Rinse it out, then mop it up. Rent or purchase a steam cleaner. Steam the floor following the instructions on the cleaner. Make a paste of baking soda and water. Mix 3 parts of baking soda to 1 part water to make a thick paste.

This versatile cleaner will work with all colors of grout, but vinegar can be harmful to some natural stones such as marble or limestone. Apply the paste to the grout lines with your finger. Although the baking soda isn’t harmful, wearing rubber gloves can help prevent scratches or irritated skin from the abrasive grout and baking soda. Make a 1:1 solution of white vinegar and water in a spray bottle. Wait for the solution to stop bubbling. Scrub the grout lines with a brush. Use a nylon bristled scrub brush, or a toothbrush, to scrub along each grout line. Pay close attention to corners and edges to make these areas clean as well. Mop the floor with plain water. Dissolve 2 tablespoons of oxygenated bleach into 2 cups of warm water. Test a hidden corner of the grout before cleaning the entire floor. Pour the oxygen bleach solution onto the grout. Use a nylon bristle brush to scrub the oxygen bleach solution into the grout lines. Allow the oxygen bleach solution to sit on the grout for several minutes for optimum results.

Scrub the grout with the brush back and forth.carpet cleaning lincoln ca Be sure to scrub in corners and around the floor’s edges as dirt and grime tends to accumulate here.top carpet cleaners in atlanta ga Dip the brush into the oxygenated bleach powder to increase cleaning power. what is the best steam mop you can buyIf you find a stain that is darker or more noticeable, a stronger solution of oxygen bleach can be made by dipping your wet brush directly into the oxygen bleach powder. NOTE Pour a small amount of the powder into a separate container to avoid mixing water into your main container of oxygen bleach powder. Rinse the floor with water and dry.Mix ¾ cup baking soda, ¼ cup hydrogen peroxide, and 1 tablespoon dish soap.

This highly effective paste cleans the grout in three ways:[3] The baking soda works as a natural abrasive to scrub the grout. The hydrogen peroxide chemically reacts with the baking soda releasing bleaching oxygen ions. The dish soap helps loosen dirt and remove grease. NOTE: The bleaching action of the chemical reaction may affect colored grout. Test a hidden corner before cleaning the entire floor. Apply the paste with a nylon bristled brush. Let the mixture sit on the grout for 15 minutes. Rinse the grout with warm or hot water to remove all of the solution. Pour a small amount of water directly onto the tile floor to rinse the solution off the grout. Use caution as wet tiled floors can be very slippery. Use a rag to wipe the grout to remove any leftover residue or dirt. Mop the floor with clean water.Steam cleaners can effectively clean and sanitize all types of tiles and grouts as there are no chemicals involved. Visit your local home improvement store to find a machine to rent or buy.

Make sure that the steam cleaner you acquire has the proper attachments for cleaning grout:[4] Follow the manufacturer’s directions to assemble and fill the steam cleaner. Fill the reservoir with clean water to the fill line according to the manual’s instructions. Turn the steam cleaner on and allow it to heat up. Move the cleaning brush back and forth over the grout. Use a towel or mop to wipe up the excess moisture after cleaning. You should always test a new cleaner or cleaning solution on an inconspicuous spot to make sure it is not going to damage your grout or tile. When using baking soda or oxygen bleach solutions, don’t make more than you need because these solutions can lose their potency quickly. After cleaning the grout, apply a sealant to keep it cleaner longer. Do not use a hard bristled brush like a steel or wire brush because this may break and damage the grout Don’t use vinegar on any real marble, granite, travertine, or other natural stone because it might etch the surface and cause permanent damage.

The grout used with these surfaces should only be cleaned with a ph neutral solution.Q: DEAR TIM: Cleaning a tile floor is my next big project. The grout lines are filthy, and I haven't discovered an easy way to restore the tile. Is there a magic product that will clean floor tile? Once the grout is clean, what's the easiest way to keep it that way? Should I invest in a cleaning machine? -- Michelle S., Corvallis, Ore. A: DEAR MICHELLE: We had a boatload of tile floors in our last home, and cleaning them was a nightmare. To make it worse, we had brilliant white tile with light gray grout in our kitchen and breakfast area. I knew when I was installing it that it was going to be a challenge to keep it clean. Add to the mix three small kids, and soon the grout around the refrigerator, stove and kitchen sink was nearly black. It took me years to discover how to clean tile floors in a way that was easy and that didn't harm my family, pets and the colored grout. I finally settled on using powdered oxygen bleach.

Little did I know that this choice would put me way ahead of the current green movement. Oxygen bleach is nontoxic, doesn't produce harsh fumes, and is color- and fabric-safe. It removes all food and grease stains with no or minimal scrubbing. The oxygen ions attack the stain molecules, breaking them into pieces that rinse away with little effort. To clean floor tiles, mix any high-quality oxygen bleach with warm water and stir it until it dissolves. Then pour the solution onto the floor tile so the grout lines are flooded with the solution. It's best to apply the oxygen-bleach solution to dry grout so it soaks deeply. Let the solution sit on the grout for at least 15 minutes. If it completely soaks into the grout, add more solution, making sure there is always plenty of the cleaning liquid on the grout. The longer you let the solution sit on the grout, the less work you have to do cleaning tile flooring. The oxygen ions work for up to six hours. To get maximum cleaning results, it helps to scrub the grout lightly after 30 minutes.

Always pour new solution onto the grout as you scrub. An oxygen bleach solution will remove red wine stains in minutes. Beet juice is not a problem. I've not discovered one stain it can't remove. Friends have tried the tile cleaning machines, but they say the oxygen bleach does a much better job. You have to always scrub a little, but that's how anything gets clean. Once you have clean floor tiles, you can keep the grout looking like new by adding oxygen bleach powder to your mop water. Apply a liberal amount of mop water to the floor, scrubbing the tile surface with the mop. But leave the mop water in the grout joints without rinsing the floor. The oxygen ions clean the light dirt in the grout without scrubbing. Come back 30 minutes later and rinse the floor with clean water. If you do this each time, you'll never be on your hands and knees again with a scrub brush. It's always best to work on stains while they're fresh, if at all possible. But tile floors that have been dirty for years will come clean in no time if you use oxygen bleach.