Julia Butler Hanson 2015 Pool Fees & Schedule Maximum pool occupancy is 75 people Swimming on Saturday is free for the first 50 patrons. We rent the pool for birthday parties, reunions, and private parties.There is a two hour minimum for pool rentals.Advanced reservation and payment in required to reserve the pool. 25 or fewer people 26 – 50 people Weekdays from 6:00-7:00 am and 5:30-6:30 pm. Lap swimmers must be able to swim 25 yds. continuously and follow lap swim etiquette. Weekdays from 7:30-8:30 am and from 5:30-6:30pm. Lifeguard led swim lessons with a maximum number of 6 students per instructor. Each child is $25.00 for 10 half hour sessions Private Lessons are by appointment only through the pool office. Price is based on instructor to student ratio per 30 minute session. Julia Butler Hansen Municipal Swimming Pool is located nest to Wahkiakum High School, at 500 Third St., Cathlamet. Julia Butler Hansen Pool Schedule

Updated June 2015 (subject to change). Please check the bulletin boards to see about late night swims and other special events! POOL TELEPHONE NUMBER: 360-795-6515 Julia Butler Hansen Swimming PoolSecurity swimming pool cover / with rods Mambo is simple to use: Simply pull on a strap to roll it out. Roll it up without stress or strain using a crank. No complicated mechanisms, no risk of breakdown. A single cover to install for years of care-free enjoyment.You escape the nuisance of seasonal cover changes and the drudgery: cleaning, folding and storing the cover removed unfolding and installation of the other cover. Choose comfort, choose Mambo. Mambo is easy to keep: With its two lacquered surfaces, Mambo stays clean, it is easily washed down with a blast of water.The Floatron is a pool-cleaning device that claims to be greener than the rest, according to its manufacturers. Not only does the $270 gadget radically reduce your chlorine use, but its manufacturers also claim that it purifies your pool water to EPA drinking water standards.

When the 12-inch gizmo is floating in the pool, its photovoltaic panel converts the sunlight into a harmless, low-power electricity current. The current then energizes a specially alloyed mineral electrode, causing the release of mineral ions into the water. This ionized water controls the growth of micro-organisms naturally and efficiently, it says.carpet cleaning supplies hawaiiOne Floatron is powerful enough to clean a 40,000-gallon pool. carpet cleaners for wool rugsAnd on top of that, your kids can use it as the most expensive Frisbee ever made—although I am waiting for one of you to send me a link to a bling-studded disc commissioned long ago by P. Diddy to play Fetch with La Lopez.best way to clean wool oriental rug

Solar Pool Cleaner [Go Sun Solutions] It is important to remember to clean out the old caulk on and in the surfaces where you will be re-applying new caulk. Traces of dirt, paint, oil and old caulk left behind will only lead to problems later on. Use foam backer rod in joints that are 1/4" or wider to get better results and to save money. carpet cleaners cape town cbdFor those joints that are under heavy stress, such as in swimming pools, also think about using a primer. best cleaner for wool carpetsRemoval and Cleaning: Good surface and joint preparation is the real beginning of a professional and long-lasting caulking job, whether replacing old caulk or sealing a new joint for the first time. best pool vacuum for dirt

By using a putty knife, painter's 5-in-1 tool or other similar tool, remove all of the old caulk in the joint. A heat gun can be used to soften old caulk and loose paint to make removal easier, or a 3M Indoor/Outdoor caulk-remover can also help remove all types of old caulk. The surface needs to be completely free of old caulk, peeling paint, weathered wood fibers, grease, oil, wax, dirt, rust, frost, moisture, etc. A wire brush works well to remove contaminants, and a drill-mounted wire wheel is often the best answer for cleaning dirty, unsound concrete. To remove some contaminants like oil or grease, it may be necessary to wipe the joint down with a solvent-laden rag, letting the solvent completely evaporate before caulking. Remember, the best caulk in the world won't work if it is applied to a dirty or unsound surface. Backer Rod: If the joint or crack to be sealed is 1/4" wide or wider, it is best to install a foam backer rod in the joint - to the proper depth - before applying the caulk.

Reasons to Use a Backer Rod: It saves money. A backer rod is generally cheaper than a good quality caulking compound, and most of the joint can be filled with the backer rod before the actual sealant is installed. It provides the means to form an "hourglass" cross-sectional shape to the bead of sealant. This geometric shape allows the sealant to handle the inevitable joint movement much more easily than any other configuration. The reason: Large surface areas of adhesion are established at the sides of the joint, while a relatively thin cross-section of sealant is left in the center of the joint to allow for easy flexing. It provides a "bond-breaking" surface at the rear of the joint or crack that prevents the sealant from establishing three-point adhesion - which, if allowed to occur, can lead to early failure. It allows for additional pressure to be applied to the sealant during the "tooling" process, which further favors more sealant being forced into intimate contact with the sides of the joint for better adhesion.

Tip: A backer rod is easily installed in joints by simply pressing the material into the recess to a depth that will allow the thickness of the sealant to be approximately 1/2 that of the width of the joint. It can be installed just by pressing it into place with a finger or an appropriately sized tool. If you are using closed-cell backer rod, it is important to avoid damaging the surface of the rod (such as with holes or nicks) because wherever such damage occurs there is a risk of "out-gassing" from the backer rod and forming blisters in the sealant. (Note: An open-cell backer rod does not have this problem, but it has a much greater tendency to absorb water and hold it - with potentially very negative effects on the sealant - if the integrity of the sealant is breached at a later date.) Then, masking tape can be applied to both sides of the joint before caulking to prevent smearing on the exposed surfaces adjacent to the joint. Primers: If the joint or crack is in an area that will be subjected to particularly difficult stress, such as continual water submersion at the bottom of a swimming pool, it is important to use a primer before caulking.