User ReviewedHow to Clean Grout Between Floor Tiles Four Methods:Using Baking Soda and VinegarCleaning with Oxygenated BleachCleaning Grout with Hydrogen Peroxide, Baking Soda, and Dish SoapCleaning Grout with a Steam CleanerCommunity Q&A Even after mopping, tile floors with dirty grout may still look messy. You can make your floors look fresher by cleaning the grout between the tiles. This wikiHow will show you how to do that. Apply a paste made from baking soda and water to the grout. Spray it down with diluted vinegar. Scrub it with a brush, rinse it, then wipe it dry. Pour a solution made from oxygenated bleach and warm water onto the grout. Scrub it with a brush, rinse it, then mop it up. Use a brush to scrub a paste made from hydrogen peroxide, baking soda, and dish soap into the grout. Rinse it out, then mop it up. Rent or purchase a steam cleaner. Steam the floor following the instructions on the cleaner. Make a paste of baking soda and water. Mix 3 parts of baking soda to 1 part water to make a thick paste.

This versatile cleaner will work with all colors of grout, but vinegar can be harmful to some natural stones such as marble or limestone.best lightweight portable vacuum cleaner Apply the paste to the grout lines with your finger.best buy cylinder vacuum cleaner Although the baking soda isn’t harmful, wearing rubber gloves can help prevent scratches or irritated skin from the abrasive grout and baking soda.steam carpet cleaners bristol Make a 1:1 solution of white vinegar and water in a spray bottle.buy pool filter sand australia Wait for the solution to stop bubbling.best home remedy carpet cleaner

Scrub the grout lines with a brush. carpet cleaner irvine caUse a nylon bristled scrub brush, or a toothbrush, to scrub along each grout line. Pay close attention to corners and edges to make these areas clean as well. Mop the floor with plain water. Dissolve 2 tablespoons of oxygenated bleach into 2 cups of warm water. Test a hidden corner of the grout before cleaning the entire floor. Pour the oxygen bleach solution onto the grout. Use a nylon bristle brush to scrub the oxygen bleach solution into the grout lines. Allow the oxygen bleach solution to sit on the grout for several minutes for optimum results. Scrub the grout with the brush back and forth. Be sure to scrub in corners and around the floor’s edges as dirt and grime tends to accumulate here. Dip the brush into the oxygenated bleach powder to increase cleaning power. If you find a stain that is darker or more noticeable, a stronger solution of oxygen bleach can be made by dipping your wet brush directly into the oxygen bleach powder.

NOTE Pour a small amount of the powder into a separate container to avoid mixing water into your main container of oxygen bleach powder. Rinse the floor with water and dry.Mix ¾ cup baking soda, ¼ cup hydrogen peroxide, and 1 tablespoon dish soap. This highly effective paste cleans the grout in three ways:[3] The baking soda works as a natural abrasive to scrub the grout. The hydrogen peroxide chemically reacts with the baking soda releasing bleaching oxygen ions. The dish soap helps loosen dirt and remove grease. NOTE: The bleaching action of the chemical reaction may affect colored grout. Test a hidden corner before cleaning the entire floor. Apply the paste with a nylon bristled brush. Let the mixture sit on the grout for 15 minutes. Rinse the grout with warm or hot water to remove all of the solution. Pour a small amount of water directly onto the tile floor to rinse the solution off the grout. Use caution as wet tiled floors can be very slippery.

Use a rag to wipe the grout to remove any leftover residue or dirt. Mop the floor with clean water.Steam cleaners can effectively clean and sanitize all types of tiles and grouts as there are no chemicals involved. Visit your local home improvement store to find a machine to rent or buy. Make sure that the steam cleaner you acquire has the proper attachments for cleaning grout:[4] Follow the manufacturer’s directions to assemble and fill the steam cleaner. Fill the reservoir with clean water to the fill line according to the manual’s instructions. Turn the steam cleaner on and allow it to heat up. Move the cleaning brush back and forth over the grout. Use a towel or mop to wipe up the excess moisture after cleaning. You should always test a new cleaner or cleaning solution on an inconspicuous spot to make sure it is not going to damage your grout or tile. When using baking soda or oxygen bleach solutions, don’t make more than you need because these solutions can lose their potency quickly.

After cleaning the grout, apply a sealant to keep it cleaner longer. Do not use a hard bristled brush like a steel or wire brush because this may break and damage the grout Don’t use vinegar on any real marble, granite, travertine, or other natural stone because it might etch the surface and cause permanent damage. The grout used with these surfaces should only be cleaned with a ph neutral solution.Removing old grout from tiled surfaces is a task that requires a few simple tools and some patience. The main component of most grouts is Portland cement. It usually takes a newly grouted surface several days or weeks to become fully hardened. Once it has cured, however, old grout can be difficult to clean from tiled floors and walls. Your first instinct may be to chisel it off with a metal tool, such as a putty knife, but this can damage the tiles. Instead, a process of soaking and gently scraping and scouring the grout with non-metal tools is recommended. Pour some clean water over the tile surface.

This will act as a lubricant and will prevent scratches on the tiled surface as you work. Scrape the large clumps or layers of grout with a small piece of hardwood, such as oak, that is about 1/4 to 3/8 inch thick, with a square-cut end. Do not use metal scraping tools such as putty knives; these will permanently damage the glazed surface of the tile. Work at the grout with light to medium pressure until you’ve removed all heavy deposits of grout, and then rinse off the tile with clean water. Wet the grout that remains with clean water, and scour the surface of the tile with a damp nylon scouring pad. As you scour, keep the pad wet with plenty of water. Rinse the tile with clean water, and wipe it dry with a clean towel. If the grout still is not fully removed, continue scouring. Round the end of your wood piece using coarse-grit sandpaper until it resembles a wood chisel. Apply water to the tile surface and push and pull the stick between the tiles to smooth the grout lines. Mix 1 cup of white granulated sugar into a gallon of hot water.